T-Con Board Repair in KL & Selangor — Half Screen, Lines or No Picture?
Half the screen is dark, lines run across the picture, or the TV shows sound but no image? The T-Con board is one of the most common causes — and one of the most repairable. We test the board, the LVDS cable and the panel ribbons at our Petaling Jaya workshop. Free diagnosis, written quote before any repair.
Independent repair service since 2010 — not a brand authorised centre. Free workshop diagnosis · 1-month warranty on specific parts · Pickup RM 40–80 by zone.
What the T-Con Board Actually Does
The T-Con (Timing Controller) sits between the main board and the LCD panel. It receives the video signal from the main board over the LVDS cable, converts it into precisely timed pulses, and sends those pulses to the panel's gate and source drivers. Without correct timing, the panel cannot form a stable image — even if the backlight and main board are working perfectly.
Signal conversion
Converts video data from the main board into the timing signals the panel needs. No T-Con output means no usable image, even with sound and backlight working.
Voltage generation
Generates the gate and source voltages (VGH, VGL, AVDD, gamma references) that drive the panel. Failed voltage rails cause lines, half-screen and colour faults.
Panel timing
Controls the row and column timing across the panel. A timing fault produces symptoms that look like panel damage but may be board-level repairable.
T-Con vs Mainboard vs Panel — How We Tell Them Apart
This is the most important step before any repair. A T-Con fault, a main-board fault and a panel fault can produce almost identical symptoms — but the repair cost and outcome are very different. We separate them before quoting.
| What you see | T-Con fault | Mainboard fault | Panel fault |
|---|---|---|---|
| Menu and on-screen display | Menu may also be distorted or broken up | Menu usually normal; one input may be affected | Menu shows the same fixed lines or half-screen |
| Lines or half-screen | Often movable or changing with input | Usually not line-pattern specific | Fixed in the same position on every source |
| No picture with sound | Backlight on, no image | Could be input or video-processing fault | Panel not drawing an image |
| Repair route | Cable reseat, board repair or replacement | Board-level repair or replacement | Usually not economical |
This table is a starting guide, not a diagnosis. The same symptom can overlap between all three — a fixed line on the panel can sometimes be a T-Con output fault, and a moving line can sometimes be a panel driver fault. We confirm the exact source with voltage testing and signal checks at the workshop. If there is no image at all, start with the black-screen guide →
Common T-Con Board Symptoms
These are the patterns we see most often when the T-Con board is involved. None of them proves the board is faulty on its own — but they narrow the diagnosis before we open the TV.
Vertical or horizontal lines
Persistent lines across the picture — often the first visible sign of a T-Con timing or voltage-rail fault. Lines that change with the image are more likely board-related; fixed lines are more likely panel-related.
Half-screen dark or half-screen image
One side of the screen is dark, washed out or showing a different image. A clean vertical division between the two halves often points toward a T-Con output or panel ribbon issue rather than the panel itself.
Colour distortion, negative or washed-out image
Colours appear inverted, solarised, too white or badly shifted. This often points to the gamma IC or gamma reference voltages on the T-Con board — a component that can sometimes be repaired without replacing the whole board.
No picture with sound and backlight on
The TV powers on, sound works and the backlight is lit, but no usable image appears. This is a classic T-Con symptom — but a main-board video-output fault can produce the same result, so both are tested.
How We Diagnose and Repair a T-Con Fault
Same sequence on every TV — from the simplest cable check to board-level repair.
Signal and menu check
Confirm the symptom on the TV menu and across inputs — separates a T-Con fault from an input-device fault.
LVDS and ribbon inspection
Check the LVDS cable from main board to T-Con, and the panel ribbons from T-Con to the panel. Oxidised or loose ribbons are a common cause.
Voltage and signal test
Measure T-Con voltage rails (VDD, VGH, VGL, AVDD, gamma references) and check the LVDS signal where possible.
Repair, replace or advise
Cable reseat or clean, component-level repair where viable, or exact-part board replacement. Panel faults are told honestly and not pushed as a repair.
T-Con Board Repair Cost in Malaysia
T-Con repair is usually one of the more economical TV repairs — a T-Con board is a small fraction of the cost of a new panel. Workshop diagnosis is free — a written quote is provided before any repair.
| Repair | Typical range | Notes |
|---|---|---|
| Diagnosis / inspection | FREE | Written quote before any repair. |
| LVDS / ribbon cable reseat or clean | RM 100–200 | If the cable is the confirmed cause — often the simplest fix. |
| T-Con board repair (component-level) | RM 150–780+ | Size-based: 32–43" 150–280+ · 48–55" 320–440+ · 60–84" 480–780+. |
| T-Con board replacement | Quoted after part match | Exact model and board part number required. Price depends on availability. |
| Panel fault (if T-Con is not the cause) | Usually not economical | We tell you honestly if the fault is the panel, not the T-Con. |
A rough guide: T-Con repair usually makes sense when the quote is well below half the price of a comparable new TV — which is most of the time. If the diagnosis shows panel damage instead, replacement is usually the better choice. This is not a fixed rule; it depends on the TV's age and exact fault. We give you a specific view after diagnosis.
Estimates only — exact charges confirmed after diagnosis. Pickup RM 40–80 depending on location. Turnaround: 1–2 days if part in stock, 3–5 days if ordered.
Repair the T-Con, or Is It a Panel Fault?
This is the honest split — and it is why diagnosis matters before any board is ordered.
When the fault is on the board
- Lines or half-screen that change with the image
- No picture with sound and backlight on
- Colour distortion or gamma faults
- LVDS or ribbon cable issue
When the panel is the cause
- Fixed line in exactly the same position on every input and on the menu
- Physical crack, dark patch or internal delamination
- Panel driver IC failure confirmed after T-Con is ruled out
- Quote approaches the price of a comparable new TV
A T-Con board can look like panel damage — and a panel can look like a T-Con fault. We test the board and the signal path before telling you which one it is. If the fault is the panel, we say so plainly rather than quoting a board that will not fix it. For the panel side, see cracked panel assessment →
What We Verify on Every T-Con Fault
Every T-Con quote is backed by the same checklist — including the cable and panel-ribbon checks that many workshops skip before ordering a board.
The T-Con pre-quote check
This checklist runs on every TV that arrives with a suspected T-Con fault, whether it comes by pickup or drop-off.
- Menu and on-screen display checked — confirms whether the fault is inside the TV or from an external source.
- LVDS cable inspected — seating, oxidation and continuity checked before the board is suspected.
- Panel ribbon cables inspected — the flex cables from T-Con to the panel are a common cause of lines and half-screen faults.
- T-Con voltage rails measured — VDD, VGH, VGL and gamma references checked against model-specific values.
- Board part number matched — T-Con boards are model-specific and sometimes panel-specific; exact number confirmed before ordering.
- Panel fault ruled out — fixed lines or panel driver symptoms are identified before a board is ordered.
What this means for you: the WhatsApp reply gives you a price range. The confirmed final quote comes after these checks — and if the fault is the panel, we tell you before you spend anything on a board.
T-Con Board Repair — Your Questions
Direct answers. If your question is not here, WhatsApp us with the TV model and a photo of the screen.
How do I know if my TV has a T-Con fault or a panel fault?
There is no single test that proves it from the outside. A T-Con fault often produces lines or half-screen that change with the image, or no picture with sound and backlight on. A panel fault often produces a fixed line in exactly the same position on every input and on the TV menu. The only reliable separation is voltage testing and signal checks at the workshop — we confirm the source before quoting.
Can a T-Con board be repaired, or does it have to be replaced?
Depends on the fault. Oxidised or loose ribbon cables can often be cleaned and reseated. Some board faults — such as a failed gamma IC or a shorted capacitor — can be repaired at component level. If the board is beyond component repair, we match the exact part number and quote replacement. We explain which route applies after inspection.
My TV has a half-screen picture — is that always the T-Con?
No. Half-screen faults can come from the T-Con board, the panel ribbon cables or the panel itself. A clean vertical division between the two halves often points toward a T-Con or ribbon issue, but a soft or uneven division can point toward the panel. We check the ribbons and T-Con output before concluding.
How much does T-Con board repair cost in Malaysia?
Workshop diagnosis is free. Cable reseat is typically RM 100–200. T-Con board repair is size-based: RM 150–280+ for 32–43 inch, RM 320–440+ for 48–55 inch, and RM 480–780+ for 60–84 inch. Replacement is quoted after the exact part number is matched. Panel faults are usually not economical, and we say so plainly.
Can I replace the T-Con board myself?
We do not recommend it. T-Con boards are model-specific and sometimes panel-specific — a board that looks identical may be programmed for a different panel. The LVDS and ribbon connectors are also fragile and easy to damage. If you are unsure of the exact part number, a wrong board will not fix the fault and may add cost.
Do all TVs have a separate T-Con board?
No. Some TVs integrate the T-Con function into the main board or into the panel assembly. On those models there is no separate T-Con board to replace, and the repair route is different. We confirm whether your model has a separate board before quoting.
Do you offer pickup and drop-off for T-Con repairs?
Yes. Pickup is available in selected KL and Selangor areas for RM 40–80 depending on location, and drop-off is free at our Petaling Jaya workshop — J-G 12, Jalan PJS 2, Taman Medan Jaya, 46000 Petaling Jaya, Selangor. The repair price is the same whether you drop off or choose pickup.
What warranty do you provide on a T-Con repair?
1-month warranty on the specific parts we supply. It does not cover new physical damage, liquid damage, power surges or unrelated faults. Full warranty terms.
Different Symptom? Check the Closest Match Below
If the symptom is not lines, half-screen or a T-Con fault pattern, one of these pages may be closer.
Sound but no picture
Completely black with sound — no lines, no half-screen. Backlight or T-Con territory, diagnosed separately.
No-picture guideScreen lines or flicker
Lines, flicker or a picture that cuts in and out — start with the Picture Test on this page.
Line & flicker diagnosisFaint image with torch
Dark screen but image visible with a torch — LED strip failure, not a T-Con signal fault.
LED strip repairDead TV — no power
No standby light at all — power-board fault, not a T-Con signal issue.
Dead TV diagnosisClicking or dead but flickers
If flicker is tied to clicking sounds, the power board may be involved — not a T-Con issue.
Component-level testingPanel / cracked screen
Physical panel damage or a fixed line that stays on every input — honest assessment first.
Cracked panel assessmentFull price list
Every fault type, every size, every band — the complete reference.
See all pricesWhat warranty covers
What our 1-month warranty on specific parts covers for a repaired T-Con fault.
Read warranty termsT-Con Repair Across KL & Selangor
Kuala Lumpur: pickup for suspected T-Con faults in selected KL neighbourhoods. Selangor: drop-off at our Petaling Jaya workshop, or pickup in covered Selangor districts. T-Con faults need bench testing, so workshop diagnosis is the standard route.
Send Us Your TV Model and a Photo of the Fault
Tell us the brand, model, size, and what the screen is doing — half-screen, lines, colour distortion or no picture with sound. We reply with a likely cause and a price range before you bring it in.